Nissan Maxima QX

1. Prop up forward wheels antiretractable boots. Weaken wheel nuts, a back of the car and establish to a poddomkratta it on props. Remove back wheels.
2. Otboltite from a rack a basic arm of a brake hose. On the models equipped with ABS turn out a coupling bolt of a collar and separate a plait of an electrical wiring of the wheel sensor from a rack.
3. Without disconnecting a hydraulic hose, remove a support of the brake mechanism and a brake disk (see the Head the Brake system). Tie up a support a wire to an element of the bottom or a suspension bracket, - try not to allow tension of a brake hose.
4. If the rack needs replacement, remove assembly of a nave with the wheel bearing.
5. Disconnect from a rack longitudinal and cross levers (see the Section Removal and installation of levers of a back suspension bracket (models 1993 and 1994 of of the issue)).
6. Open a cover of the luggage compartment and remove the corresponding panels of internal finishing for the purpose of ensuring access to fixture of the top support of rack-mount assembly.
7. Remove a rubber cover of a support of the shock-absorber. Ask the assistant to hold rack-mount assembly and give the top fixing nuts. take assembly from under the car through a wheel arch. If the rack needs replacement, disconnect from it an arm of the longitudinal lever and transfer to replaceable assembly. track that fixture was tightened with the required effort.

Act according to the instructions provided in paragraphs 6 and 7 of the Section Removal, check of a state and installation of rack-mount assemblies of a forward suspension bracket. The description of the procedure of dismantling are resistant (if in it there is a need) see in the Section Replacement of the Shock-absorber / Screw of a spring of rack-mount assembly.

1. Having used the help of the assistant, get a rack on the regular space for an arch of a wheel and accurately pass hairpins of its top support throughout reciprocal body openings. Screw, but do not tighten so far, fixing nuts.
2. Connect to a rack longitudinal and cross levers (see the Section Removal and installation of levers of a back suspension bracket (models 1993 and 1994 of of the issue)). Prop up a back suspension bracket a jack, having got the last under an arm of the longitudinal lever, - components have to are hung out at normal working height. Tighten fixture cross and longitudinal levers with the required effort.
3. Fix a basic arm of a brake hose on a rack. On models with ABS establish an arm of fastening of an electrical wiring of the wheel sensor.
4. Establish wheels, lower the car on the earth and tighten wheel nuts with the required effort (see the Head Nastroyki and routine maintenance).
5. Tighten with the required effort of a nut of the top support of a rack. Establish to the place of the panel of an internal upholstery of the luggage compartment.

1. Prop up forward wheels antiretractable boots. Weaken wheel nuts, a back of the car and establish to a poddomkratta it on props. Remove back wheels.

2. Give a nut of a bolt of fastening of the lower end of the shock-absorber to assembly of the back bridge.

3. Nuts of fastening of the top support of rack-mount assembly are located in the luggage compartment, - remove the corresponding panels of an internal upholstery. Ask the assistant to hold assembly and give the top fixing nuts. Take a rack from under the car through a wheel arch.

1. Act according to the instructions provided in paragraphs 6 and 7 of the Section Removal, check of a state and installation of rack-mount assemblies of a forward suspension bracket.
2. The description of the procedure of dismantling are resistant (if in it there is a need) see in the Section Replacement of the Shock-absorber / Screw of a spring of rack-mount assembly.

1. Having used the help of the assistant, get a rack on the regular space for an arch of a wheel and accurately pass hairpins of its top support throughout reciprocal body openings. Screw, but do not tighten so far, fixing nuts.
2. Connect the lower end of the shock-absorber to assembly of the back bridge, pass a fixing bolt throughout openings. Prop up a suspension bracket a jack, bring components to normal working height and tighten a nut of a fixing bolt with the required effort.

The jack should be got under an arm of the longitudinal lever of a suspension bracket, - at all not under levers!

3. Tighten with the required effort of a nut of the top support of a rack. Establish to the place of the panel of an internal upholstery of the luggage compartment.