Nissan Maxima QX

since 1993 release

Repair and operation of the car



Nissan Maxima QX
+ Cars of the Nissan Maxima brand
+ Maintenance instruction
+ Settings and routine maintenance
+ Engine
+ Cooling systems, heating
+ Power supply system and release
+ Engine electric equipment
+ Control systems of the engine
+ Transmission
+ Coupling and power shafts
+ Brake system
- Suspension bracket and steering
   General information
   Removal, check of a state and installation of rack-mount assemblies of a forward suspension bracket
   Replacement of the shock-absorber / screw spring of rack-mount assembly
   Removal and installation of assembly of a rotary fist with a nave
   Removal and installation of assembly of a forward nave with the wheel bearing
   Removal and installation of the forward stabilizer of cross stability
   Removal and installation of a control lever of a forward suspension bracket
   Replacement of spherical support
   Removal, check of a state and installation of racks of a back suspension bracket
   Removal and installation of assembly of a back nave with the wheel bearing
   Removal and installation of a bar of the back stabilizer of cross stability (models 1993 and 1994 of of the issue)
   Removal and installation of levers of a back suspension bracket (models 1993 and 1994 of of the issue)
   Removal and installation of components of a back suspension bracket of models since 1995 of the issue.
   Removal and installation of a steering wheel
   Removal and installation of tips of steering drafts
   Replacement of protective covers of assembly of the steering mechanism
   Removal, dismantle and installation of rack transfer
   Removal and installation of the steering pump
   Removal of air from a hydraulic path of system of strengthening of a wheel
   Replacement of wheel hairpins
   Wheels and tires - the general information
   Angles of installation of wheels
+ Body
+ Onboard electric equipment



Removal and installation of assembly of a rotary fist with a nave

 Remember that the dust produced in the course of operation of brake mechanisms may contain extremely unhealthy asbestos of the person. Do not blow off dust compressed air at all and do not inhale it, - at service of mechanisms put on a protective mask or a respirator. Do not use for rubbing of components of the brake system gasoline or solvents on an oil basis at all, - apply only company cleaners or methyl alcohol!

REMOVAL

 PERFORMANCE ORDER

1. Take off a decorative cap of a disk or a cover of a stupichny nut. Take the forelock and wring out a tag of a lock washer, then weaken a stupichny nut (see the Head Stsepleniye and power shafts).

 If the face head does not pass in an opening in the center of a wheel, temporarily install to the place of the last the spare wheel.

2. Weaken nuts of fastening of a wheel, a front of the car and establish to a poddomkratta it on props. Remove a wheel.
3. Remove a support of the brake mechanism and a brake disk (see the Head the Brake system). Release a brake hose from an arm on rack-mount assembly. On the equipped ABS models disconnect an electrical wiring and remove the wheel sensor.
4. Give nuts of fastening of a rack of a suspension bracket to a rotary fist, however, do not beat out still fixing bolts.
5. Release from the lever of a rotary fist a tip of steering draft (see the Section Removal and installation of tips of steering drafts).
6. Release a spherical support from assembly of a rotary fist (see the Section Removal and installation of a control lever of a forward suspension bracket).
7. Beat out fixing bolts and separate a rotary fist from rack-mount assembly, at the same time pushing out a pin of a power shaft from a wheel nave (if the shaft "stuck", use the hammer and a brass drift). Tie up the released power shaft a wire to suspension bracket elements.

INSTALLATION

 PERFORMANCE ORDER

1. Grease vents of a pin of a power shaft with universal lubricant. Start assembly of a rotary fist on the regular place, pass a pin of a power shaft throughout a nave.
2. Fill a fist in a rack flange, pass bolts, then screw, but do not tighten, fixing nuts.
3. Connect a suspension bracket control lever to a rotary fist (see the Section Removal and installation of a control lever of a forward suspension bracket).
4. Fill in the fist lever a tip of steering draft (see the Section Removal and installation of tips of steering drafts). Tighten with the required effort of a nut of bolts of fastening of a rack, and also support fixture to the lever and a draft tip nut.
5. Install on a nave a brake disk and other components of the brake mechanism (see the Head the Brake system).
6. Screw a stupichny nut and tighten it strongly, but it is not final yet.
7. Establish a wheel. Lower the car on the earth and tighten wheel nuts with the required effort (see the Head Nastroyki and routine maintenance).
8. Finally tighten a stupichny nut with the required effort, do not forget to record it the new forelock (see the Head Stsepleniye and power shafts).