Nissan Maxima QX

since 1993 release

Repair and operation of the car


Nissan Maxima QX
+ Cars of the Nissan Maxima brand
+ Maintenance instruction
+ Settings and routine maintenance
+ Engine
+ Cooling systems, heating
+ Power supply system and release
+ Engine electric equipment
+ Control systems of the engine
+ Transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
- Body
   General information and precautionary measures
   Care of components of a body and bottom of the car
   Care of vinyl elements of finishing
   Care of an upholstery and carpets of salon
   Repair of insignificant damages of body panels
   Repair of seriously damaged body panels
   Service of loops and locks of the car
   Replacement wind and other fixed glasses
   Removal and installation of a decorative front grille
   Removal, installation and adjustment of provision of a cowl
   Removal and installation of a latch of the lock of a cowl and cable of its drive
   Removal and installation of forward and back bumpers
   Removal and installation of forward wings
   Removal and installation of the panel of a forward reflector
   Removal and installation of panels of an internal upholstery of doors
   Removal, installation and adjustment of doors
   Removal and installation of a latch, cylinder of the lock and handles of a door
   Removal and installation of door glasses
   Removal and installation of regulators of window regulators
   Removal and installation of rear-view mirrors
   Removal, installation and adjustment of a cover of the luggage compartment
   Removal and installation of a latch and cylinder of the lock of a cover of the luggage compartment
   Removal and installation of driving cables of an otpuskaniye of locks of a cover of the luggage compartment and door of the hatch of a jellied mouth of the fuel tank
   Removal and installation of the central console
   Removal and installation of finishing sections of the dashboard
   Removal and installation of sections of a casing of a steering column
   Removal and installation of the main section of the dashboard
   Removal and installation of seats
   Removal and installation of the back shelf
   Adjustment of the top hatch
   Body sizes
+ Onboard electric equipment

Body

Specifications

Body geometry

By means of sensors of swing achieve the correct installation of wheels (back wheels have to be strictly in a track of lobbies), - track correctness of installation of sensors and equality of lengths of indexes.

When using a roulette (it is desirable metal) you watch that her measuring tape was overwound it was bent.

The image of an asterisk (*) after value in a point of measurement demonstrates that the second point of measurement is symmetrized by rather specified.

The distances measured on three main directions act as coordinates of points of measurement ("X", "Y", "Z").

Arrangement of coordinate axes at measurement of geometrical parameters of a body of the car

FR Forward
LH Left board
RH Right board
"X-X" Diametrical plane of the car
"Y-Y" the Vertical plane passing through an axis of forward wheels of the car
"Z-Z" Main plane


Measurement points

Tag on the center of a first line of an aperture of a motive compartment

Top central support of a radiator

Left back corner of an aperture of a motive compartment

Forward longeron

Support of a rack and forward longeron

Forward longeron

Top support of a radiator

Front panel


Geometry of a motive compartment of models 1993 and 1994 of of the issue.

 

 

 

Radiator basis support (forward part) and forward suspension bracket (it is located below previous) and forward longeron (is closer to the center)

 

Back and central elements

 

Geometry of a motive compartment of models of 1995 of the issue.

 

Measurement points

Top central support of a radiator

Top party of a support of a radiator, Forward longeron, cover Ledge, Convex tag,

Outer side of an aperture of a motive compartment

Center and bottom edge of a radiator

Support of a rack of a suspension bracket and forward longeron (left board)

Forward longeron

Top central support of a radiator

Right forward longeron


Geometry of body elements of the bottom of models since 1995 of the issue.

 

 

Coordinates

And, and
Х: 330
Y:-710
Z: 188.8

B, b
X: 513
Y:-540
Z: 322

C, with
X: 450
Y: 68
Z: 184

D, d
X: 441
Y: 354
Z: 111.5

E, e
X: 600
Y: 430
Z: 154.9

F, f
Х: 412
Y: 700
Z: 109

G, g
X: 414.5
Y: 1.210
Z: 108.4

H, h
X: 412
Y: 1.625
Z: 104

J, j
Opening of installation of a core of a suspension bracket
X: 555
Y: 2.185
Z: 239.5

To
X: 512
Y: 3.000
Z: 326.6

k
X:-544
Y: 2.982
Z: 328.2

L
X: 540
Y: 3.272
Z: 326.6

l
X:-575
Y: 3.280
Z: 326.6

M
X: 546
Y: 3.454
Z: 295.4

m
X:-570.5
Y: 3.450
Z: 326.

Centers of forward and back top support of racks of a suspension bracket

Coordinates
N, n
Х: 548.8
Y: 28.7
Z: 779.3

Oh, about
X: 490.3
Y: 2.621
Z: 537.2

Lobby: N, n to 87 dia.

Back: Oh, about 61,4 dia

 

Opening of installation of draft of a suspension bracket

Element of a forward suspension bracket