Nissan Maxima QX

1. Disconnect a negative wire from the battery and wait not less than three minutes before starting dismantle of a slip.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action!

2. Remove assembly of the combined switch (see below the subsection Replacement).
3. By means of an ohmmeter or the lamp sampler equipped with the individual power supply check correctness of distribution of conductivity between switch plugs in its various provisions.

Position of the switch	Existence of conductivity between plugs
Head headlights are switched off, situation C	5 and 6, 8 and 9
Parking fires, situation A or B	11 and 12
Parking fires, situation C	5 and 6, 8 and 9, 11 and 12
Head headlights, situation A or C	5 and 6, 8 and 9, 11 and 12
Head headlights, situation B	5 and 7, 8 and 10, 11 and 12
Head headlights, situation C	5 and 6, 8 and 9, 11 and 12
Indexes of the right turn	1 and 2
Indexes of the left turn	1 and 3
Indexes of the right turn / side repeater	61 and 62
Indexes of the left turn / side repeater	61 and 63

Position of the switch	Existence of conductivity between plugs
Vykl	13 and 14
Interval mode	13 and 14, 15 and 17
Slow mode	17 and 17
Bystry mode	16 and 17
Glass washing	17 and 18

4. In case of identification of violations replace the switch.

1. Disconnect a negative wire from the battery and wait not less than three minutes before starting dismantle of a slip.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action!

2. Remove a steering wheel (see the Head Podvesk and steering).
3. Remove a driver's knee emphasis and covers of a casing of a steering column (see the Head Kuzov).

4. Turn out four fixing screws and remove from the combined switch spring contact of a driver's safety cushion (see the Head Podvesk and steering). Turn out screws of fastening of assembly of the combined switch.

5. Remove assembly of the combined switch from a steering column and disunite contact sockets of an electrical wiring.

6. Turn out screws of fastening of the individual switch which is subject to replacement and remove the last from the case of the combined switch.

7. Connect the new switch to plugs of the contact socket, - track reliability of fixing of assembly in a block.
8. Further assembly is made as it should be the return to an order of dismantle of components. The description of the procedure of installation of spring contact of a safety cushion is provided in the Head Podvesk and steering.

1. The panel of switches of management of functioning of a tempostat (except the switch On/off) is installed on the right on a steering wheel of the car.

2. Remove the switch (see below). By means of an ohmmeter or the lamp sampler equipped with the individual power supply check correctness of distribution of conductivity between switch plugs in its various provisions.

Position of the switch	Existence of conductivity between plugs
Resume/Accel (Return/acceleration)	1 and 3
Set/Coast (Installation/setup)	1 and 2
Cancel (Dumping)	1 and 3 *, 1 and 2 * (with diodes)
* Diodes are used, check both directions

3. The faulty switch is subject to replacement.

1. Disconnect a negative wire from the battery and wait not less than three minutes before starting dismantle of a slip.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action!

2. Having hooked the screw-driver passed throughout a special groove, uncover the panel.

3. Turn out fixing screws, remove assembly of the switch and disconnect from it an electrical wiring.

4. Installation is made upside-down.