Nissan Maxima QX

since 1993 release

Repair and operation of the car



Nissan Maxima QX
+ Cars of the Nissan Maxima brand
+ Maintenance instruction
+ Settings and routine maintenance
+ Engine
+ Cooling systems, heating
+ Power supply system and release
+ Engine electric equipment
+ Control systems of the engine
+ Transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
- Onboard electric equipment
   General information and precautionary measures
   Search of causes of failures of electric equipment
   Safety locks and fusible inserts - the general information
   Chain breakers - the general information
   The relay - the general information and check of serviceability of functioning
   Check of serviceability of functioning and replacement of the breaker of indexes of turns / alarm system
   Check of serviceability of functioning and replacement of understeering switches
   Check of serviceability of functioning and replacement of the switch of ignition and lock of blocking of a steering column
   Check of serviceability of functioning and replacement of switches of the dashboard
   Check of serviceability of functioning of measuring instruments of temperature of the engine and fuel consumption
   Removal and installation of a combination of devices
   Removal and installation of the radio receiver and loudspeakers
   Removal and installation of the antenna of the radio receiver
   Replacement of lamps of head headlights
   Adjustment of the direction of optical axes of head headlights
   Removal and installation of block headlights
   Replacement of lamps
   Check of serviceability of functioning, removal and installation of an electric motor of the drive of screen wipers
   Check of serviceability of functioning and replacement of horns of a horn
   Running fires of daylight (DRL)
   Check of serviceability of functioning and recovery repair of a heater of back glass
   Control system of speed (темпостат) - general information and check of serviceability of functioning
   The electric drive of window regulators - general information and check of serviceability of functioning
   The uniform lock - general information and check of serviceability of functioning
   The electric drive of external rear-view mirrors - general information and check of serviceability of functioning
   The electric drive of the top hatch - general information and check of serviceability of functioning
   The electric drive of front seats - general information and check of serviceability of functioning
   Transfer of management of functioning of onboard consumers of the electric power on dial-up lines
   Safety cushions - the general information
   + Schemes of electric connections



Adjustment of the direction of optical axes of head headlights

 PERFORMANCE ORDER

 Violation of adjustment of the direction of optical axes of head headlights can lead to dazzle of drivers of the vehicles moving a parallel course and be the reason of creation of an emergency on the road. Check of correctness of adjustment of headlights has to be made regularly time in 12 months, and also every time after replacement of block headlights and performance of repair of the bearing car front elements. It is necessary to draw the attention of readers to that fact that the procedure described below can be considered only preventive control. Final adjustment of optical axes has to be made in a specialized workshop of car service!

1. Each of block headlights is equipped with two sprung adjusting screws: internal and external. One of screws serves for adjustment of provision of a block headlight in the horizontal plane, the second - in vertical. Access to both screws opens from the back party of a block headlight. On models of early years of release one adjusting rod behind and one from above is provided. Since 1995 both rods are sent to the issue back.

2. There are several methods of check of correctness of adjustment of the direction of optical axes of head headlights of the car. Below the simplest of them who is not demanding any special skills from the performer and not needing use of the special equipment is described.

3. Drive the car a front to a wall. Paste on a wall an adhesive tape strip on the vertical line passing in the diametrical plane of the car. Also paste vertical strips of an adhesive tape on the lines passing through the centers of projections to a wall of lenses of head headlights.

4. Paste on a wall horizontally located adhesive tape strip on the line drawn through the centers of projections of lenses of head headlights to a wall surface. Remark: It is simpler to make this procedure, having adjusted the car closely to a wall.
5. For performance of adjustment of the direction of optical axes of head headlights roll away the car from a wall on distance about 7.6 m.

 The platform on which the car is placed has to have a plain horizontal surface, it is desirable with a hard coating. The fuel tank of the car has to be filled half, from salon and the luggage compartment all heavy objects breaking centering of the car are taken.

6. Begin with adjustment of the direction of an optical axis of passing beam. Try to achieve rotation of adjusting screws of block headlights such arrangement of light spots that zones with the maximum intensity of lighting it appeared in about 50 mm below the horizontal line and is touch sizes more right than vertical.
7. Having finished the first adjustment, turn on driving beam: zones of the maximum intensity of illumination have to be displaced in the direction of crossing of vertical lines from horizontal, having been slightly lower than the last.

It is not possible to receive equally full centering of beams of both near, and driving beam in practice. It is necessary to try to achieve some compromise solution taking into account features of operation of the car, keeping the aspiration to ensure the maximum traffic safety in the head of a corner.

8. At the first opportunity drive away the car on car repair shop for performance of adjustment of the direction of optical axes of head headlights with use of the special equipment.