Nissan Maxima QX

since 1993 release

Repair and operation of the car


Nissan Maxima QX
+ Cars of the Nissan Maxima brand
+ Maintenance instruction
+ Settings and routine maintenance
+ Engine
+ Cooling systems, heating
+ Power supply system and release
+ Engine electric equipment
+ Control systems of the engine
+ Transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
- Onboard electric equipment
   General information and precautionary measures
   Search of causes of failures of electric equipment
   Safety locks and fusible inserts - the general information
   Chain breakers - the general information
   The relay - the general information and check of serviceability of functioning
   Check of serviceability of functioning and replacement of the breaker of indexes of turns / alarm system
   Check of serviceability of functioning and replacement of understeering switches
   Check of serviceability of functioning and replacement of the switch of ignition and lock of blocking of a steering column
   Check of serviceability of functioning and replacement of switches of the dashboard
   Check of serviceability of functioning of measuring instruments of temperature of the engine and fuel consumption
   Removal and installation of a combination of devices
   Removal and installation of the radio receiver and loudspeakers
   Removal and installation of the antenna of the radio receiver
   Replacement of lamps of head headlights
   Adjustment of the direction of optical axes of head headlights
   Removal and installation of block headlights
   Replacement of lamps
   Check of serviceability of functioning, removal and installation of an electric motor of the drive of screen wipers
   Check of serviceability of functioning and replacement of horns of a horn
   Running fires of daylight (DRL)
   Check of serviceability of functioning and recovery repair of a heater of back glass
   Control system of speed (темпостат) - general information and check of serviceability of functioning
   The electric drive of window regulators - general information and check of serviceability of functioning
   The uniform lock - general information and check of serviceability of functioning
   The electric drive of external rear-view mirrors - general information and check of serviceability of functioning
   The electric drive of the top hatch - general information and check of serviceability of functioning
   The electric drive of front seats - general information and check of serviceability of functioning
   Transfer of management of functioning of onboard consumers of the electric power on dial-up lines
   Safety cushions - the general information
   + Schemes of electric connections

Replacement of lamps

 Flasks of lamps remain hot within about 20 minutes after shutdown of lighting fixtures. Before getting to work make sure that components finally cooled down.

Forward dimensional fires / indexes of turns

 PERFORMANCE ORDER

1. The car also establish to Poddomkratta it on props.

2. Access to assemblies of indexes of turns and marker lights opens from below.

3. The boss of a marker light is taken by a pulling from the landing nest. The cartridge of the index of turn needs also to be turned. For extraction of a lamp from the boss it needs to be pressed and turned counterclockwise.

Side marker lights

 PERFORMANCE ORDER

1. Open a cowl, turn out the screw located near a casing of a head block headlight then shake assembly of a side marker light (on models of early years of release - the repeater of the index of turn). Pull assembly strictly outside and release it from the body panel.

2. Take a lamp from the boss and replace it new.

Back marker lights and stoplights

The lamps located in a body part of the combined lamp

 PERFORMANCE ORDER

1. Open a cover of the luggage compartment. Uncover an observation port in the panel of internal finishing for the purpose of ensuring access to assembly of the back combined lamp. The boss of an external lamp it is equipped with a rubber cap. For ensuring access to a lamp of a marker light it is necessary to remove a plastic cover.

2. For extraction of a lamp from the boss it should be wrung out down and to turn counterclockwise.

The lamps located in the part of lantern assembly placed on a cover of the luggage compartment

 PERFORMANCE ORDER

1. Open a cover of the luggage compartment and turn out two screws of fastening of a plate of a lamp holder on the back party of lantern assembly.

2. For extraction of a lamp from the boss it should be wrung out down and to turn counterclockwise.

Illumination of registration plate

 PERFORMANCE ORDER

1. Turn out fixing screws and remove a lens from assembly of a lamp of illumination of registration plate. For the purpose of ensuring access to a lamp extend a cartridge from assembly.

2. For extraction of a lamp pull it strictly back.

Stoplights of the top level

 PERFORMANCE ORDER

Wring out a cover of lantern assembly to the right, the son-in-law pull it and remove. The lamp is just extended from the boss.

Illumination of devices

 PERFORMANCE ORDER

Remove a combination of devices (see the Section Removal and installation of a combination of devices). Lamps are taken from a back part of the printed circuit board of a combination of devices.

Internal lamps (salon, luggage compartment)

 PERFORMANCE ORDER

1. For removal of plafonds of mate lamps / the saloon lamp it should be hooked the small screw-driver.
2. For extraction of mate lamps they should be turned in the boss. The two-socle lamp of the ceiling lamp is just extended from the sprung contact plugs of the boss. Try not to touch flasks barehanded, - formation of fatty spots can significantly lower lamp service life.