Nissan Maxima QX

since 1993 release

Repair and operation of the car



Nissan Maxima QX
+ Cars of the Nissan Maxima brand
+ Maintenance instruction
+ Settings and routine maintenance
+ Engine
+ Cooling systems, heating
+ Power supply system and release
- Engine electric equipment
   General information and precautionary measures
   Start of the engine from the auxiliary power supply
   Check of a state and replacement of the battery
   Check of a state and replacement of wires of the battery
   System of ignition - the general information and precautionary measures
   Check of functioning of system of ignition
   Check of a state and replacement of coils of ignition
   Check of a state and replacement of the power transistor (models 1993 and 1994 of of the issue)
   Check, adjustment, removal and installation of the distributor of ignition (models 1993 and 1994 of of the issue)
   Check and adjustment of installations of a corner of an advancing of ignition
   System of a charge - the general information and precautionary measures
   Check of a condition of system of a charge
   Removal and installation of the generator
   System of start - the general information and precautionary measures
   Check of serviceability of functioning of a starter and chain of start
   Removal and installation of a starter
   Replacement of the traction relay
+ Control systems of the engine
+ Transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment

Removal and installation of a starter

S114-461 starter design (models 1993 and 1994 of of the issue)

1 — the Holder
2 — the Coupling
3 — the Bolt (6.4 ÷ 7.8 Nanometers)
4 — the Case
5 — Pruzhina
6 — the Adjusting washer
7 — the Nut (7.4 ÷ 9.8 Nanometers)
8 — the Cover
9 — the Returnable spring
10 — the Lock ring
11 — the Lever
12 — the Boot

13 — the Traction relay
14 — the Anchor
15 — an excitement Winding
16 — the Case
17 — the Brush (-)
18 — Pruzhina of a brush
19 — the Back cover
21 — the Bolt (4.9 ÷ 6.4 Nanometers)
22 — the Brush (+)
23 — the Shaft


S114-801A starter design (models since 1995 of the issue)

1 — the gear wheel Case
2 — the Adjusting lever
3 — the Boot
4 — the Traction relay
5 — the Washer
6 — the Nut (7.4 ÷ 9.8 Nanometers)
7 — the Slip
8 — the Gear wheel of internal gearing
9 — Bolts (4.9 ÷ 6.4 Nanometers)
10 — Bolts (6.4 ÷ 7.8 Nanometers)
11 — a gear wheel Emphasis
12 — the Gear wheel
13 — the Lock ring

14 — the Central suspension bracket (Р)
15 — a gear wheel Shaft
16 — Planetary transfer
17 — the Central suspension bracket (And)
18 — the Case
19 — the Anchor
20 — the Brush (+)
21 — the Brush (-)
22 — Pruzhina of a brush
23 — the Persistent washer
24 — the Back cover
25 — the Brush holder


 PERFORMANCE ORDER

1. The design of a starter is presented on illustrations.
2. Disconnect a negative wire from the battery.

 If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action!

3. Remove assembly of the air cleaner with an inlet air duct (see the Head of the Power supply system and release).
4. Disconnect an electrical wiring from assembly of a starter with the traction relay.

5. Give fixing bolts and separate assembly of a starter from the engine.