Nissan Maxima QX

since 1993 release

Repair and operation of the car

Nissan Maxima QX
+ Cars of the Nissan Maxima brand
+ Maintenance instruction
+ Settings and routine maintenance
+ Engine
+ Cooling systems, heating
+ Power supply system and release
- Engine electric equipment
   General information and precautionary measures
   Start of the engine from the auxiliary power supply
   Check of a state and replacement of the battery
   Check of a state and replacement of wires of the battery
   System of ignition - the general information and precautionary measures
   Check of functioning of system of ignition
   Check of a state and replacement of coils of ignition
   Check of a state and replacement of the power transistor (models 1993 and 1994 of of the issue)
   Check, adjustment, removal and installation of the distributor of ignition (models 1993 and 1994 of of the issue)
   Check and adjustment of installations of a corner of an advancing of ignition
   System of a charge - the general information and precautionary measures
   Check of a condition of system of a charge
   Removal and installation of the generator
   System of start - the general information and precautionary measures
   Check of serviceability of functioning of a starter and chain of start
   Removal and installation of a starter
   Replacement of the traction relay
+ Control systems of the engine
+ Transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment

Removal and installation of the generator

Generator design (models 1993 and 1994 of of the issue)


1 — the Pulley 2 — the Forward cover 3 — the Rotor 4 — the Back bearing 5 — the Nut (39 ÷ 59 Nanometers) 6 — the Forward bearing	7 — the Holder of the bearing 8 — the Stator 10 — Brush assembly 11 — the Back cover 12 — Coupling bolts (3.1 ÷ 3.9 Nanometers)

Generator design (models since 1995 of the issue)


1 — the Pulley 2 — the Forward cover 3 — the Forward bearing 4 — the Holder of the bearing 5 — the Rotor 6 — the Contact ring 7 — the Stator 8 — Coupling bolts (3.1 ÷ 3.9 Nanometers)	9 — contact installation Details 10 — the Condenser 11 — the Brush holder 12 — the Regulator 13 — Diode assembly 14 — Laying 15 — the Back cover

Models 1993 and 1994 of of the issue.

PERFORMANCE ORDER

1. The design of the generator is presented on an illustration.
2. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action!

3. The car also establish to Poddomkratta it on props. At the corresponding complete set remove protection of a case.
4. Take off a driving belt (see the Head Nastroyki and routine maintenance).
5. Disconnect an electrical wiring and a final wire from the generator.
6. Turn out fixing bolts and separate the generator from the engine block.

7. Installation is made upside-down.
8. Do not forget to establish in conclusion a driving belt and to connect a negative wire to the battery. Adjust effort of a tension of a belt (see the Head Nastroyki and routine maintenance).

Models since 1995 of the issue.

PERFORMANCE ORDER

The car also establish to Poddomkratta it on props. At the corresponding complete set remove protection of a case and a loker of protection of an arch of the right forward wheel.
3. Take off a driving belt (see the Head Nastroyki and routine maintenance).

4. Disconnect an electrical wiring and a final wire from the generator.

5. Remove assembly of fans of the cooling system with a casing (see the Head of the Cooling system, heating).
6. Remove the K/V compressor and, without disconnecting hydraulic lines, shift it aside.

7. Turn out fixing bolts and separate the generator from the engine block.

8. Installation is made upside-down.
9. Do not forget to establish in conclusion a driving belt and to connect a negative wire to the battery. Adjust effort of a tension of a belt (see the Head Nastroyki and routine maintenance).