Nissan Maxima QX

since 1993 release

Repair and operation of the car



Nissan Maxima QX
+ Cars of the Nissan Maxima brand
+ Maintenance instruction
+ Settings and routine maintenance
+ Engine
+ Cooling systems, heating
+ Power supply system and release
+ Engine electric equipment
+ Control systems of the engine
+ Transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
- Body
   General information and precautionary measures
   Care of components of a body and bottom of the car
   Care of vinyl elements of finishing
   Care of an upholstery and carpets of salon
   Repair of insignificant damages of body panels
   Repair of seriously damaged body panels
   Service of loops and locks of the car
   Replacement wind and other fixed glasses
   Removal and installation of a decorative front grille
   Removal, installation and adjustment of provision of a cowl
   Removal and installation of a latch of the lock of a cowl and cable of its drive
   Removal and installation of forward and back bumpers
   Removal and installation of forward wings
   Removal and installation of the panel of a forward reflector
   Removal and installation of panels of an internal upholstery of doors
   Removal, installation and adjustment of doors
   Removal and installation of a latch, cylinder of the lock and handles of a door
   Removal and installation of door glasses
   Removal and installation of regulators of window regulators
   Removal and installation of rear-view mirrors
   Removal, installation and adjustment of a cover of the luggage compartment
   Removal and installation of a latch and cylinder of the lock of a cover of the luggage compartment
   Removal and installation of driving cables of an otpuskaniye of locks of a cover of the luggage compartment and door of the hatch of a jellied mouth of the fuel tank
   Removal and installation of the central console
   Removal and installation of finishing sections of the dashboard
   Removal and installation of sections of a casing of a steering column
   Removal and installation of the main section of the dashboard
   Removal and installation of seats
   Removal and installation of the back shelf
   Adjustment of the top hatch
   Body sizes
+ Onboard electric equipment

Removal and installation of finishing sections of the dashboard

Dashboard design

1 — the Deflector of an obduv of a windshield
2 — Docking knot
3 — the Remote insert
4 — the Clamp of fastening of the deflector
5 — the Clamp
6 — the Sealing ring
7 — the Combination of devices
8 — the Clamp
9 — the Clamp
10 — the Decorative cover of the fixing screw

11 — the Clamp
12 — the Decorative cover of the fixing screw
13 — the Assembly bracket
14 — the Control panel of functioning of a heater and To/in
15 — the Ware box
16 — Facing of the lever of switching
17 — the Facing slip
18 — the Decorative cover of the fixing screw
19 — the Slip
20 — the Decorative cover of the fixing screw


 The models of cars considered in the present manual are equipped with system of additional safety (SRS). Before starting performance of any works near the block of a safety cushion, a steering column or the dashboard, disconnect SRS in order to avoid getting injured at its casual operation (see the Head Onboard electric equipment). It is easy to distinguish an electrical wiring of a chain of SRS on yellow color of isolation.


The design of the dashboard is presented on an illustration.

Disconnect a negative wire from the battery.

 If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action!

Facing of an instrument guard

 PERFORMANCE ORDER

1. Uncover a casing of a steering column (see the Section Removal and installation of sections of a casing of a steering column).

2. Turn out two fixing screws in the top part of facing of an instrument guard. Accurately hooking the screw-driver wound by an adhesive tape, release clamps and separate the lower part of facing of a guard from the dashboard.

 On the models equipped with a control system of speed or anticreeping system in facing the corresponding switches from which at the last stage of removal of the panel it is necessary to disconnect an electrical wiring are built in.

3. Installation is made upside-down. Track reliability of a zashchelkivaniye of clamps.

Knee emphasis

 PERFORMANCE ORDER

1. Uncover the saloon assembly block of safety locks, then turn out two screws located on bottom edge of the panel of a knee emphasis. Remove persistent assembly.

2. If the emphasis is removed for the purpose of ensuring access to other components, it is enough to turn out fixture and to lower the panel.

3. Installation is made upside-down.

Central section of finishing

 PERFORMANCE ORDER

1. Having hooked the screw-driver wound by an adhesive tape, remove the central section of finishing from the car dashboard.

2. Having separated the panel, disconnect an electrical wiring from the switches which are built in in it (see the Head Onboard electric equipment).
3. Installation is made upside-down.

Ware box

 PERFORMANCE ORDER

1. Open a ware box and turn out four top and two lower screws of fastening of assembly. Take a casing of a ware box from the dashboard.

2. Installation is made upside-down.