Nissan Maxima QX

since 1993 release

Repair and operation of the car



Nissan Maxima QX
+ Cars of the Nissan Maxima brand
+ Maintenance instruction
+ Settings and routine maintenance
+ Engine
+ Cooling systems, heating
+ Power supply system and release
+ Engine electric equipment
+ Control systems of the engine
+ Transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
- Body
   General information and precautionary measures
   Care of components of a body and bottom of the car
   Care of vinyl elements of finishing
   Care of an upholstery and carpets of salon
   Repair of insignificant damages of body panels
   Repair of seriously damaged body panels
   Service of loops and locks of the car
   Replacement wind and other fixed glasses
   Removal and installation of a decorative front grille
   Removal, installation and adjustment of provision of a cowl
   Removal and installation of a latch of the lock of a cowl and cable of its drive
   Removal and installation of forward and back bumpers
   Removal and installation of forward wings
   Removal and installation of the panel of a forward reflector
   Removal and installation of panels of an internal upholstery of doors
   Removal, installation and adjustment of doors
   Removal and installation of a latch, cylinder of the lock and handles of a door
   Removal and installation of door glasses
   Removal and installation of regulators of window regulators
   Removal and installation of rear-view mirrors
   Removal, installation and adjustment of a cover of the luggage compartment
   Removal and installation of a latch and cylinder of the lock of a cover of the luggage compartment
   Removal and installation of driving cables of an otpuskaniye of locks of a cover of the luggage compartment and door of the hatch of a jellied mouth of the fuel tank
   Removal and installation of the central console
   Removal and installation of finishing sections of the dashboard
   Removal and installation of sections of a casing of a steering column
   Removal and installation of the main section of the dashboard
   Removal and installation of seats
   Removal and installation of the back shelf
   Adjustment of the top hatch
   Body sizes
+ Onboard electric equipment

Removal, installation and adjustment of doors

 Doors of the car I have the considerable weight therefore it will be reasonable to secure with the help of the assistant.

REMOVAL AND INSTALLATION

 PERFORMANCE ORDER

1. Remove the panel of an internal upholstery and the film insulating screen (see the Section Removal and installation of panels of an internal upholstery of doors). Disunite contact sockets and push an electrical wiring through technological openings in a doorframe, having provided thereby a possibility of free dismantle of the last.
2. Open a door against the stop and prop up it a jack, or wooden blocks. Remark: In order to avoid damage of LKP lay a rags layer between a head of a jack and edge of a door.

3. Turn out a bolt of fastening of the limiter of opening of a door.

4. Lead round loopy levels a marker, having marked situation them on a door.

5. Turn out fixing bolts and by means of the assistant accurately remove door assembly from the car. Installation is made upside-down.

ADJUSTMENT

 PERFORMANCE ORDER

1. Correctness of provision of a door in a body aperture has critical value from the point of view of serviceability of functioning of door assembly. First of all it is necessary to estimate the size of a side play of axial fingers of door loops. Completely open a door and pull it up-down. If the side play of a door exceeds 1.6 mm, loops should be replaced.
2. For performance of correction of the provision of a door in the vertical direction weaken bolts of fastening of loops on a car body (access to some bolts is limited therefore the key of a special form can be necessary). The door can be considered established truly when its upper edge falls into a closed position it is parallel to a car roof cut, and lower - lines of a threshold
3. Alignment of a door in the longitudinal direction is carried out by an otpuskaniye of bolts of fastening of loopy levels on a doorframe, - the special key can be necessary again. The first line (back at a back door) doors at the same time has to appear aflush with the surface of a wing.
4. Correct operation of the locking mechanism can achieve by updating of the provision of the drummer of the lock in the vertical direction. For assessment of size of shift lead round a plate of the basis of the drummer a marker. Weaken fixture and make necessary adjustment, - the latch has to enter gearing with the central part of the drummer.

5. In conclusion adjust position of the drummer in the horizontal direction, - the closed door has to appear aflush with the surface of the rack/panel of a back wing and regularly at the same time be locked.