The device, service, repair of Nissan Maxima QX - Removal and installation of a latch of the lock of a cowl and cable of its drive//Nissan of Maxim (since 1993)

Nissan Maxima QX

since 1993 release

Repair and operation of the car



Nissan Maxima QX
+ Cars of the Nissan Maxima brand
+ Maintenance instruction
+ Settings and routine maintenance
+ Engine
+ Cooling systems, heating
+ Power supply system and release
+ Engine electric equipment
+ Control systems of the engine
+ Transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
- Body
   General information and precautionary measures
   Care of components of a body and bottom of the car
   Care of vinyl elements of finishing
   Care of an upholstery and carpets of salon
   Repair of insignificant damages of body panels
   Repair of seriously damaged body panels
   Service of loops and locks of the car
   Replacement wind and other fixed glasses
   Removal and installation of a decorative front grille
   Removal, installation and adjustment of provision of a cowl
   Removal and installation of a latch of the lock of a cowl and cable of its drive
   Removal and installation of forward and back bumpers
   Removal and installation of forward wings
   Removal and installation of the panel of a forward reflector
   Removal and installation of panels of an internal upholstery of doors
   Removal, installation and adjustment of doors
   Removal and installation of a latch, cylinder of the lock and handles of a door
   Removal and installation of door glasses
   Removal and installation of regulators of window regulators
   Removal and installation of rear-view mirrors
   Removal, installation and adjustment of a cover of the luggage compartment
   Removal and installation of a latch and cylinder of the lock of a cover of the luggage compartment
   Removal and installation of driving cables of an otpuskaniye of locks of a cover of the luggage compartment and door of the hatch of a jellied mouth of the fuel tank
   Removal and installation of the central console
   Removal and installation of finishing sections of the dashboard
   Removal and installation of sections of a casing of a steering column
   Removal and installation of the main section of the dashboard
   Removal and installation of seats
   Removal and installation of the back shelf
   Adjustment of the top hatch
   Body sizes
+ Onboard electric equipment



Removal and installation of a latch of the lock of a cowl and cable of its drive

 The models of cars considered in the present manual are equipped with system of additional safety (SRS). Before starting performance of any works near the block of a safety cushion, a steering column or the dashboard, disconnect SRS in order to avoid getting injured at its casual operation (see the Head Onboard electric equipment). It is easy to distinguish an electrical wiring of a chain of SRS on yellow color of isolation.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action!

Latch

 PERFORMANCE ORDER

1. Lead round assembly of a latch a marker or a chertilka for the purpose of a guarantee of correctness of its installation at assembly. Unhook a spring and by means of the screw-driver release a lock otpuskaniye cable tip from assembly of a latch.

2. Installation is made upside-down.

 Adjust the provision of a latch so that the cowl was reliably fixed by the lock in a closed position, - rubber pillows of support have to be flattened slightly.

Driving cable

 PERFORMANCE ORDER

1. Disconnect a driving cable of an otpuskaniye of the lock of a cowl from assembly of a latch.

2. In interior of the car turn out three fixing screws and separate the cowl lock otpuskaniye lever from the dashboard. Disconnect a cable from the lever.

3. Involve assembly of a cable in salon, accurately pushing it through the plug through passage in a partition.
4. Pass a tip of a new cable throughout the plug through passage in a partition and involve assembly in a motive compartment for a wire through a partition in a motive compartment, having held on its end to a cowl lock latch.
5. You make further assembly as it should be, the return to a dismantle order.