Nissan Maxima QX

since 1993 release

Repair and operation of the car


Nissan Maxima QX
+ Cars of the Nissan Maxima brand
+ Maintenance instruction
+ Settings and routine maintenance
+ Engine
+ Cooling systems, heating
+ Power supply system and release
+ Engine electric equipment
+ Control systems of the engine
+ Transmission
+ Coupling and power shafts
- Brake system
   General information
   System of anti-blocking of brakes (ABS) - the general information and codes of malfunctions
   Replacement of brake shoes of disk brake mechanisms
   Removal and installation of supports of disk brake mechanisms
   Check of a state, removal and installation of a brake disk
   Replacement of boots of drum brake mechanisms of back wheels
   Removal and installation of wheel cylinders
   Removal and installation of the main brake cylinder
   Replacement of the dosing valve regulator
   Check of a state and replacement of brake lines and hoses
   Pumping of the brake system
   Check of serviceability of functioning/tightness, replacement and adjustment of the vacuum amplifier of brakes
   Adjustment of the parking brake
   Replacement of a cable(s) of the drive of the parking brake
   Adjustment of a pedal of a foot brake
   Check of serviceability of functioning and replacement of the sensor switch of stoplights
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment

Replacement of a cable(s) of the drive of the parking brake

The scheme of laying of the hummock drive of the parking brake is submitted on an illustration.

Scheme of laying of the torsovy drive of the parking brake

1 — the Control lever
2 — the Bolt (8 ÷ 11 Nanometers)
3 — the Adjusting nut (3.1 ÷ 4.3 Nanometers)
4 — the Nut of fastening of a basic arm of an intermediate clamp (8 ÷ 11 Nanometers)
5 — the Right back section of the hummock drive

6 — the Bolt of fastening of an arm of an intermediate clamp (8 ÷ 11 Nanometers)
7 — the Left back section of the hummock drive
8 — the Bolt (6 ÷ 11 Nanometers)
9 — the Brake mechanism of disk type
10 — the Brake mechanism of drum type

Back sections of the hummock drive

 PERFORMANCE ORDER

1. Make sure of completeness of an otpuskaniye of the parking brake.
2. Prop up antiretractable boots forward wheels, weaken nuts of fastening of back wheels, then a back of the car and establish to a poddomkratta it on props.
3. On the models equipped with drum brake mechanisms of back wheels take off brake boots and disconnect a driving cable from the executive lever of the parking brake (see the Section Replacement of Boots of Drum Brake Mechanisms of Back Wheels). Remove from the end of a cable a spring, then an otboltita the holder of a cover of a cable from a brake board. Release hummock assembly from a board of the brake mechanism.

4. On models with disk back brake mechanisms remove a lock plate of fastening of a cable to an arm, pribolchenny to a support. Release a cable from the bifurcate termination of the executive lever.

5. Otboltite all arms of intermediate clamps of fastening of a cable on elements of a frame and a suspension bracket.

6. Remove the thermofilter of the catalytic converter.

7. Give the nuts of fastening of covers of cables located at once behind assembly of the equalizer, release tips of cables from the equalizer.

8. Installation is made upside-down.
9. Make adjustment of the hummock drive of the parking brake (see the Section Adjustment of the Parking Brake).

Forward section of the hummock drive

 PERFORMANCE ORDER

1. Remove the central console (see the Head Kuzov).

2. Disconnect an electrical wiring of the sensor switch of a control lamp of raising of the parking brake.

The contact socket of an electrical wiring of the sensor switch of a control lamp of raising of the parking brake(s), nut of fastening of a control lever (V) and bolts of fastening of the directing plate (C)

3. Give an adjusting nut of the hummock drive.
4. Turn out two bolts from the control lever basis the parking brake.
5. A car back also establish to Poddomkratta it on props. Prop up forward wheels antiretractable boots and remove the thermofilter of the catalytic converter.
6. Give two nuts behind assembly of the equalizer at once and release from the last tips of back sections of the hummock drive.
7. In interior of the car turn out two bolts of fastening of the directing plate of a cable and involve in salon assembly of a forward cable with the equalizer.
8. Installation is made upside-down.
9. Make adjustment of the drive of the parking brake (see the Section Adjustment of the Parking Brake).