Nissan Maxima QX

since 1993 release

Repair and operation of the car



Nissan Maxima QX
+ Cars of the Nissan Maxima brand
+ Maintenance instruction
+ Settings and routine maintenance
- Engine
   - SOHC engines
      General information
      Preparatory actions and the list of repair procedures which can be executed without extraction of the engine from the car
      Reduction of the piston of the first cylinder in the provision of the top dead point (TDP)
      Removal and installation of covers of heads of cylinders
      Removal, check of a state and installation of assembly of yokes
      Replacement of maslootrazhatelny caps and valvate springs with plates
      Removal and installation of a gas-distributing belt and cogwheels of the GRM drive
      Removal and installation of camshafts and pushers of valves
      Removal and installation of the inlet pipeline
      Removal and installation of final collectors
      Removal and installation of heads of cylinders
      Removal and installation of a pulley of a bent shaft
      Replacement of a forward epiploon of a bent shaft
      Removal and installation of the pallet of a case of the engine
      Removal, check of a state and installation of the oil pump
      Removal and installation of a flywheel / driving disk
      Replacement of a back epiploon of a bent shaft
      Check of a state and replacement of support of a suspension bracket of the power unit
   + DOHC engines
   + General capital repairs of the engine
+ Cooling systems, heating
+ Power supply system and release
+ Engine electric equipment
+ Control systems of the engine
+ Transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment



Removal and installation of covers of heads of cylinders

REMOVAL

 PERFORMANCE ORDER

1. Dump pressure in a power supply system (see the Head of the Power supply system and release).
2. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action!

3. Mark and disconnect candle wires.
4. Remove the ignition distributor (see the Head Elektrooborudovaniye of the engine).
5. Remove the top section of the inlet pipeline (the delivery camera) (see the Section Removal and installation of the inlet pipeline).
6. Release and shift a fixing collar, then disconnect a ventilating hose (a branch pipe of a sapun) from a cover of a head of cylinders.
7. Disconnect all other hoses and plaits of an electrical wiring preventing removal of a cover.

8. Turn out fixing bolts and remove the washers established under their heads.

9. Uncover a head of cylinders.

If the cover "stuck" and does not give in to separation from a head of cylinders, accurately tap it on perimeter the hammer through wooden whetstone. In especially hard cases the layer of the dried-up sealant can be knifed shpatlevochny, - try to hook a cover the lever started under its interfaced surface as damage of the last can lead to development of leaks by no means.

INSTALLATION

 PERFORMANCE ORDER

1. The interfaced surfaces of heads of cylinders and their covers have to be absolutely pure and dry. By means of a scraper remove all traces of old sealant and fragments of the destroyed laying, then wipe surfaces with the rags moistened in acetone. Presence on the interfaced surfaces of traces of oil can lead to development of leaks.
2. In case of need banish a carving of fixing bolts a suitable lerka, restoring the damaged rounds and deleting a rust and traces of old sealant. A tap of the corresponding size banish carving openings in a head.
3. Fill a flute on the interfaced cover surface with RTV sealant, then lay new sealing laying over sealant. Let's sealant dry up and record a little thereby laying on a cover.
4. Accurately press a cover to a head of cylinders and screw fixing bolts.
5. In three-four stages tighten bolts with the required effort.
6. Further assembly is made as it should be, the return to an order of dismantle of components.
7. Start the engine and check it for existence of signs of development of leaks.