Nissan Maxima QX

since 1993 release

Repair and operation of the car



Nissan Maxima QX
+ Cars of the Nissan Maxima brand
+ Maintenance instruction
+ Settings and routine maintenance
+ Engine
+ Cooling systems, heating
+ Power supply system and release
+ Engine electric equipment
+ Control systems of the engine
- Transmission
   - 5-staged manual box of gear shifting (MBGS)
      General information
      Removal and installation of components of the drive of gear shifting
      Replacement of epiploons
      Check and replacement of the sensor switch of fires of a backing
      Removal and RKPP installation
      Capital repairs of RKPP
   + 4-staged automatic transmission (AT)
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment



Removal and installation of components of the drive of gear shifting

Gear shifting drive components

1 — the switching lever Handle
2 — the Clamp of a protective cover
3 — the Protective cover of the lever
4 — the Boot
5 — Pruzhina
6 — the gear shifting Lever
7 — the Top bearing
8 — Nizhny Novgorod the bearing
9 — the Plug
10 — the Ring
11 — the Boot
12 — the Ring
13 — the Plug
14 — Rubber laying

15 — the Holder
16 — the Nut (12 ÷ 15 Nanometers)
17 — the Bolt (4.4 ÷ 5.9 Nanometers)
18 — the Nut (35 ÷ 47 Nanometers)
19 — the Plug
20 — the Washer
21 — the Bolt (27 ÷ 36 Nanometers)
22 — the Holder of a basic bar
23 — the Basic bar
24 — the Suspension bracket of a returnable spring
25 — the Rod of management
26 — the Nut (14 ÷ 18 Nanometers)
27 — the Nut (16 ÷ 21 Nanometers)
28 — the Returnable spring

REMOVAL

 PERFORMANCE ORDER

 Some of the considered models are equipped with system of additional safety (SRS). Before starting service of the components located on proximity from safety cushions surely disconnect the SRS system (see the Head Onboard electric equipment).

1. Disconnect a negative wire from the battery. On the models equipped with SRS also disconnect a positive wire from the battery, then wait not less than three minutes, only after it you can start implementation of the procedure.

 If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action!

2. The car also establish to Poddomkratta it on props. Remove the catalytic converter and the thermofilter.

3. Disconnect a basic bar and a rod of management from transmission.

4. Give a nut of the bolt connection of fastening of a rod of management of switching to the gear shifting lever. Disconnect a returnable spring and give nuts of fastening of a basic bar to a nest of the lever and a weight damper. Remove assembly of the drive of gear shifting. Check a condition of plugs since both ends of a basic bar and a rod of management. In case of identification of cracks replace the failed components.

5. Remove the console (see the Head Kuzov). Disconnect a protective cover of the lever from the floor panel, release the lever of gear shifting and remove from it a cover, a saddle, the insulator and a reception nest. Attentively check a condition of all components, in case of identification of cracks, cuts, deformations and other mechanical damages make the corresponding replacements. Special value has faultlessness of a condition of a reception nest of the lever and its saddle, - excessive wear of these components leads to difficulties at gear shifting. The torn or cut big protective cover of the lever will be also reasonable to be replaced.

INSTALLATION

 PERFORMANCE ORDER

Installation is made upside-down. Do not forget to grease all persistent and rubbing surfaces, including a spherical support of the lever and an internal surface of its reception nest with silicone lubricant. Grease also plugs of a rod of management and a basic bar. Track reliability of tightening of fixture.